2014 Ram 3500 Steering Problems

Mileage when the problem started

• Under 25k
  729%
• 25k–50k
  729%
• 50k–75k
  313%
• 75k–100k
  28%
• 100k–150k
  313%
• 150k+
  28%

Owner reports

Selected complaints filed with NHTSA by 2014 Ram 3500 owners, lightly cleaned up (personal details are redacted by NHTSA).

The contact owns a 2014 Ram 3500. The contact stated that while operating the vehicle at highway speeds, the steering wheel felt loose, and the steering was unstable, causing the vehicle to become difficult to control. The vehicle was taken to the local dealer who diagnosed that the outboard steering linkage jam nut had become loosened. The vehicle was not yet repaired. The manufacturer was notified of the failure. The contact was informed that the VIN was not included in the NHTSA Campaign Number: 19V021000 (Steering). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 139,000.

The contact owns a 2014 RAM 3500. The contact stated that while driving at 35 MPH, the front end of the vehicle started shaking uncontrollably. There were no warning lights illuminated. The contact stated that as he released the accelerator pedal, the brake exhaust turbo engaged, then he depressed the brake pedal. The contact veered to the side of the road, inspected the vehicle, and noticed that the front support track bar bracket was fractured at the A-frame. The contact became aware that the VIN was included in NHTSA Campaign Number: 15V541000 (Steering) before he owned the vehicle; however, the recall repair was not completed at that time because the vehicle had been lifted. The contact stated that the recall repair had been marked as complete though it was not. …

There was the V06 Drag Link recall which was to weld the drag link solid with no adjustment. I had it inspected on 3 May 19 where they found the nuts not properly torqued. I told them not to weld on the truck as this would cause extra expense to me when having any future work done on the truck. Had contacted Ram Cares to get a replacement drag link installed now that a replacement part is available. That didn't happen as the appointment that I had through Ram Cares couldn't happen without DM notes. There is clucking in the steering again like before and I'm sure it has loosened up again. I confirmed with independent repair shops that they would either not touch it do to welding or charge me additional cost to remove the weld and wouldn't re-weld do to liability. If Ram was willing to supply lifetime alignments for the truck, then no problem. …

The V06 Drag Link recall of welding the adjuster doesn't allow a complete front end alignment to be done correctly. If you have had the adjuster welded, you cannot re-center the steering wheel with the adjustments that have been provided by the manufacture. This itself presents a safety issue with the steering wheel now being off centered! I have not had the welding done and have been trying to get the drag link replaced since it has become loose again! Independent repair shops won't touch a RAM truck that has been welded or not do to liability. The replacement parts are now in stock and they should be replaced since the way that RAM says to now do an alignment only allow toe and camber but not re-centering of your steering wheel. I have confirmed that with RAM service. Ram Cares has not helped in this matter. Have a previous Request #1273536 with NHTSA. …

I HAVE 27 OPEN RECALLS, the steering wheel knuckle just keeps getting looser, nothing on the column will tighten, my wipers short out , I was sold a Omission deleted truck with documentation the day of purchase it was omission deleted, I was never told this vehicle was unsafe, The manufacture wants me to pay hundreds of dollars out of pocket for them to see if it maybe safe enough . Both Chysler, and the certified dealership of ford refuse to take any accountability or action

We were traveling on a highway doing 70mph and the whole truck started to shake really badly. My husband could not steer the vehicle safely, nor could he brake without losing control. He had to slow down until the shaking stopped. When we got back on the road, the vehicle did the same thing three times. This is known issue with Dodge, yet they don't have a fix for it. They call it the "death rattle"

- Steering linkage jam broke while driving. Not sure if available truck is at dealership - I was unable to steer the vehicle while driving. I could have died and killed multiple people if a car crash had occurred - Dealer has acknowledged they inspected the part but did not perform the recall as it was not cracked. This is not the remedy listed on the NHTSA. - No warning lamps or symptoms

The bearing brackets that hold the fan clutch on explode sending the fans into the radiator. When this occurs you have limited brakes and steering. This is not first one to do this to me. This time the truck caught fire because of how hot the parts were. All of the fail on the cummins engine. Each time has been around 65mph . The shops laugh about it being another when you tow it in. Thanks richie

There was a recall on the track bar bracket in 2016. The dealership did not fix it then when we thought they did, and cleared it out of the recall system as if it was fixed. The bracket broke in 2018 and the dealership refuses to fix it because the truck has an aftermarket lift. Chrysler will not help either due to the lift. We bought the truck this way, and have no way to take the lift off as they are requesting. We want the recalled part fixed. The truck has had a death wobble since we purchased it due to this bracket. When it was still doing it after we took it to the dealership in 2016, we contacted them and they told us they didn't know why it would still be doing it. After it broke while we were driving on the highway, we realized the original bracket was still on the truck. …

I have had this truck inspected several times due to the steering bracket weld failures as per the recalls. I was recently at the metroplex Dodge on denton dr. By love filed airport in dallas and on my way home I heard a rubbing noise coming from the front passenger side wheel I noticed the wheel well cover was loose and was rubbing against the tire. Upon further inspection I noticed the welds on the spring perch bracket which is welded on the fram rails had broken off and and pushed the plastic wheel cover off. The spring perch bent upward and the spring is about to come off. Had the spring perch bracket broken off from the remaining weld wouldn of caused a roll over. One of the recalls mentioned some steering components May have welds with insufficient fusion which causes the welds to break right off. This has happened on my truck. …

Related recalls

NHTSA investigations

Steering complaints in other 3500 years